Mobile Phone Repairing Testing Methods Hot & Cold

Mobile Phone Repairing Testing Methods – Learn Hot & Cold Testing Methods of Mobile Phone Repairing for Fault Finding, Testing, Checking Mobile Components.

Mobile Phone Repairing Testing Methods – Fault Finding, Testing and Checking of Mobile Phone Parts, Components and Section of a Mobile Cell Phone can be done using the following 2 methods at the time of repairing a mobile cell phone. These methods can also be used for Fault Finding or Testing and Checking Mobile Components.

Mobile Phone Repairing Testing Methods

Table of Contents

Mobile Phone Repairing Testing Methods for Fault Finding of Mobile Components

Let us Understand these 2 Main Mobile Phone Repairing Testing Methods in Detail.

1. Cold Testing Method

When we check the value of Resistance Using a Multimeter at the time of mobile repairing and fault finding, it is called cold testing. There is no need to give any power supply to the faulty mobile phone from any equipment such as DC Power Supply or Battery during Cold Testing.

Diode Range and Beep Sound from the Multimeter are used to find fault in a mobile cell phone using the cold testing method of mobile phone repairing. In this testing method, the RED Probe of the multimeter is connected to the Ground of the Mobile Phone PCB and the BLACK Probe is touched at the Testing Points of the Mobile Phone.

During the fault finding and repairing process of each part, SMD Electronic Component or Mobile Phone Section, following correct values will be received:

1. Ear Phone Connector Tip (+ , -): .250 to .700

2. Loud Speaker / Ringer Connector Tip (+,-): .250 to .600

3. Battery Connector Tip (+): .250 to .600

4. Battery Connector Tip (Sense): above .800

5. Display Connector Supply Pins: .250 to .400

6. Display Connector Signal Pins: .500 to .800

7. Camera Connector Supply Pins: .250 to .400

8. Camera Connector Signal Pins: .600 to .900

9. Key Tip (Row and Column): .400 to .800

10. Charger Connector Tip: .600 to .700

11. Vibrator Motor Connector: .250 to .700

12. Power ON / OFF Switch Point (+): .600 to .900

13. MIC Connector Tip (Analog MIC) (+,-): .400 to .900

14. Battery Charging Out Point (+,-): .300 to .400

15. SIM Card Connector Pin 1 (V Sim): .500 to .700

16. SIM Card Connector Pin 2,3,6: .400 to .800

17. SIM Card Connector Pin 4 (GND): .00 (Beep)

18. Micro SD Card Connector Pin 4: .500 to .600

19. Micro Card Connector Pin 6 (GND): .00 (Beep)

20. Micro Card Connector Pin 1,2,3,5,7,8: .600 to .800

21. RTC: .400 to .500

22. Data RX and TX Pins: .600 to .700

2. Hot Testing Method

This is the second method of fault finding and repairing any mobile cell phone. The hot testing method is used when the fault cannot be found or when the phone cannot be repaired using the Cold Testing Method.

In this Process, VOLTAGE of damaged part, component, or section of a mobile phone is checked. The fault is found by giving Power Supply to the mobile phone with a Battery OR DC Power Supply.

In this method, the DC V (DC Volt) range of the Multimeter is selected. The BLACK Probe of the multimeter is connected with the Ground of the Mobile Phone PCB and the RED Probe is touched at the Testing Points.

During the Hot Testing method, the Voltage of different parts or sections should be as follows (All Values in Volt):

1. Ear Phone Connector Tip (+ , -) during working: .0 to 2.5

2. Loud Speaker / Ringer Connector Tip (+,-) during working: .0 to 2.5

3. Battery Connector Tip (+): 3.7

4. Display Connector Supply Pins: 1.8 to 2.9

5. Display Connector Signal Pins During Working: .0 to 1.8

6. Camera Connector Supply Pins: 1.8 to 2.9

7. Camera Connector Signal Pins During Working: .0 to 1.8

8. Key Tip (Row and Column) One Side: 1.8 to 2.8

9. Charger Connector Tip: 5 to 6

10. Vibrator Motor Connector Tip During Working: 1.9 to 3.6

11. Power ON / OFF Switch Point (+): 3 to 3.6

12. MIC Connector Tip (Analog MIC) (+,-): 1.8 to 3.0

13. Battery Charging Out Point (+,-): 3.7 to 4.2

14. SIM Card Connector Pin 1 (V Sim) When SIM Connected: 1.8 to 3.0

15. SIM Card Connector Pin 2,3,6 During Working: 0 to 2.8

16. Micro SD Card Connector Pin: 2.8

17. Micro Card Connector Pin 1,2,3,5,7,8: 0 to 2.8

18. Data RX and TX Pins: 1.8 to 2.8